1

Measurement of Resistance,Voltage, Current in A.C & D. C. Circuit by using digital Multi meter & Clamp meter

2

Verification of Super positions Theorem, Thevenin’s Theorem, Norton’s Theorem, Milliman’s Theorem, Maximum power theorem

3

Determine resonant frequency of series R-L, R-C, R-L-C circuit and study the quality factor and bandwidth.

4

Determine the resonant frequency ,Q factor & Band width of parallel resonant circuit

5

Determine the time constant of R-L-C circuit and analysis the transient response (rise time, overshoot, and damping factor from the oscilloscope)

6

Study of Low Pass filter and determination of cut-off frequency.

7

Study of High Pass filter and determination of cut-off frequency.

8

Study of Band pass Filter and Band Elimination Filter and determination of its cut-off frequency.

9

Determination of Parameters of Two Port Network (T & Y)

10

Design attenuator circuit (pie or T)

1

Familiarization of Digital Trainer Kit & Digital ICs IE 7400, 7402, 7404, 7408, 7432 & 7486.(draw their pin diagram and features)

2

Verify truth tables of AND, OR, NOT, NOR, NAND, XOR, XNOR gates using ICs& simplifications of Boolean gates

3

Implement various gates by using universal properties of NAND & NOR gates verify and truth table tabulate data.

4

Construct & verify operation of Half adder and Full adder using logic gates.

5

Construct & verify operation of Half Subtractor and Full Subtractor using logic gates.

6

Design &Implement a 4-bit Binary to Gray code converter.

7

Design & Implement a Single bit/ two bit digital comparator circuit

8

Design Multiplexer (4:1) and De- multiplexer (1:4).

9

Study the operation of flip-flops (i)S-R flip flop (ii) J-K flip flop (iii) D flip flop (iv) T flip flop

10

Realize a 4-bit asynchronous UP/Down Counter

1

(a) To study & measurement of using CRO. Voltage frequency & component testing. (b) Multimeter- measurement voltage current, resistance, components of testing & calibration.

2

To study of electric sensing device

3

To study of elastic, thermal, force & vibration sensor.

4

To study of piezo electric, thermoelectric, photoelectric transducer.

5

To study of variable resistance (resistance versus voltage& variable capacitance types measurement

6

To study about spectrum Analyzer

7

To study of LVDT & measurement Displacement versus voltage

8

To study about simple microscopes, photographic, camera

9

To study about optical fiber.

10

To study about slide projector/ overhead projector.

1

Addition, Subtraction, Multiplication, Division of two 8 bit numbers resulting 8/16 bit numbers.

2

1’’s and 2’s Complements

3

Binary to Gray Code / Hexadecimal to decimal conversion.

4

Logic Operations (AND, OR,) & Masking of bits

5

Addition, subtraction, Multiplication, Division of 16 bit nos + 2's complement of a 16 bit no.

6

Marking of specific bit of a number using look-up table

7

Largest /Smallest number of a given data array.

8

Operation of 8255 using 8085 & 8051 microcontroller

9

Study of stepper Motor and its operations (Clockwise, anticlockwise, angular movement, rotate in various speeds)

10

Initialize data to registers and memory using immediate, register, direct and indirect addressing mode

11

Write a Program for 2.1 Bit Digital Output- LED Interface & 8 Bit Digital Inputs (Switch Interface)

12

Write a Program for character based LCD Interface

1

Measurement of temperature using thermometers.

2

Measurement of temperature using RTD.

3

Measurement of temperature using thermocouple.

4

Measurement of furnace temperature using optical pyrometer.

5

Measurement of liquid level.

6

Measurement of flow using rotameter.

7

Experiment with LVDT.

8

Measurement using stain gauge.

9

Study of piezo electric transducer.

10

Measurement of force using load cell

1

Determine the Forward & reverse characteristics of any two types Diode.

2

Construct Bridge Rectifier using different filter circuit and to determine Ripple factor & Analyze wave form with filter & without filter of above circuit

3

Observe the input and output characteristics of CE & CB transistor configurations

4

Construct & test the Transistor regulator using Zener diode.

5

Study the two stage CE amplifier , find Gain & draw the frequency response curve.

6

Construct & Find the gain simple (i) Class A Amplifier. (ii) Class B Amplifier (iii) Class C Tuned Amplifier

7

Construct & test Class B -Push Pull amplifier & observe the wave form .

8

Study & observe the Drain & Transfer characteristics of JFET & MOSFET

9

Study & Calculate the frequency & Draw the wave form of the followings (i) Hartly Oscillator (ii) Collpit’s Oscillator (iii) Wein Bridge Oscillator (iv) R-C phase shift Oscillator

10

Study & test Astable, Monostable&BistableMultivibrator using OPAMP or IC 555.

1

Performance study of Differential Pressure transmitter.

2

Performance study of ON/OFF, P, PI, PID controller on flow process.

3

Performance study of ON/OFF, P, PI, PID Controller on pressure process

4

Performance study of ON/OFF, P, PI, PID Controller on Level process.

5

Performance study of ON.

6

Performance study of ON- line Pressure process Analyzer.

7

Performance study of ON- line Level process Analyzer.

8

Performance study of ON- line FLOW process Analyzer

9

Performance study of DC position control using P-I-D control action.

10

Performance study of I TO P Converter & P TO I Converter

1

Measurement of using strain Gauge

2

Measurement of using L.V.D.T and Draw the characteristics graph of Displacement versus voltage.

3

Measurement of using capacitive type Transducer and using circuit and the characteristics displacement Versus voltage.

4

To study of piezo electric Transducer.

5

To study about stroboscope.

6

To study of Hygrometer and Humidity measurement

7

Using measurement PH value of different solution.

8

Using Lab view software to design.

9

ON Line Temperature measurement method.

10

ON line pressure measurement method.

1

Study of sensor and Transducer used in Bio- Medical Application.

2

Performance study of Differential Amplifier used in Bio-Medical Instrumentation.

3

Performance study of Bio-Medical Amplifier System.

4

Performance Study of Electro-cardio-graph.

5

Performance Study of Electro-cardio-graph Recorder.

6

Performance Study of Pulse Rate counter with display.

7

Performance Study of Respiratory Recording

8

Performance Study of EEG amplifier

9

To study of operation and Maintenance of ECG Instrument.

10

Performance Study of Stethoscope.

1

Using MATLAB Software -: Introduction to MATLAB, Some basic problem based on Matrix mathematically such as (Addition, Subtraction, Multiplication, Division, Transpose using array and with -out array.

2

To Generation of different types of signal (Sinewave , Cosine wave ,Triangular ,Square ,unit Impulse ,Unit Step and Unit Ramp ,Exponential using Continuous and Discrete ).

3

Write a program and using block diagram frequency of using the combination of R-L, R-C, and R-L-C Circuit and plot.

4

Write a program unit step response of 2nd order system.

5

To Response Pole and Zero using MATLAB & Write a program open loop Transfer function of a servo system with unity feedback and determination of damping ratio.

6

To write program for closed loop Transfer Function of a System. Determine Unit step Response % Of the system.

7

To write program unity feedback control system the forward path function.

8

Sketch the polar plot and Bode plot of Transfer Function.

9

Sketch root locus as given data . G(S)=K (S+1)/(S^2(S+3.2).Sketch the T.F of Nyquist plot of the system.

10

Using system equation a system input single output system .Test for controllability.

1

Basic Logic Gates. Using Ladder logic using PLC.

2

Latching and unlatching using Ladder logic.

3

Different application push-Button.

4

Using different types Timer .Delay operation of Lamp by using Timer.

5

Using different types of Counter.

6

Sequential operation ON/OFF set of lights.

7

Traffic light indication using Ladder logic.

8

Automatic indication of Water Tank level

9

Alarm communication using SCADA.

10

Temperature sensing using SCADA